Yazar "Kanca, Erdoğan" için listeleme
-
The Effects of Using Brass and Copper Wires on the Cutting Quality of Sleipner Cold Work Steel Cut by WEDM
Ceritbinmez, Ferhat; Kanca, Erdoğan (Journal of Materials and Mechatronics, 2022)Wire electric discharge machining (WEDM) is widely used in dies, punches, aerospace and automotive sectors, since materials with high hardness, and temperature resistant, which are not possible to be cut with conventional ... -
Elektrodepolama yöntemi kullanılarak üretilmiş Ni-W/hBN kompozit kaplamaların mekanik ve korozyon özelliklerinin incelenmesi nvestigation of the mechanical and corrosion properties of Ni-W/hBN composite coatings produced usi̇ng the elektrodeposition method.
Zübarioğlu, Gözde (İskenderun Teknik Üniversitesi / Lisansüstü Eğitim Enstitüsü / Makine Mühendisliği Ana Bilim Dalı, 2023)Nikelin (Ni) korozyona karşı dayanıklılığı, sertliği, manyetik alanda boyut değiştirmesi ve adezyon kuvveti olduğu bilinmekte olup, Tungstenin (W) sert sağlam, yüksek erime sıcaklığı ve çatlak giderme yönteminde kullanıldığı ... -
Farklı bor kimyasalları ile borlanmış Inconel 625 alaşımının karakterizasyonu
Günen, Ali; Kanca, Erdoğan (Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi, 2017)Bu çalışmada, nikel bazlı süper alaşımlar içerisinde endüstride yaygın olarak kullanılan Inconel 625 alaşımı 3 farklı borlama tozu ile borlanmıştır. Kullanılan borlama tozları, %90 elementel nano bor tozu + %10 NaBF4 (NB), ... -
Farklı kireç besleme yöntemlerinin elektrik ark ocağında enerji ve süreye etkisinin incelenmesi
Kat, Sergen Ali (İskenderun Teknik Üniversitesi / Mühendislik ve Fen Bilimleri Enstitüsü / Makine Mühendisliği Anabilim Dalı, 2016)Dünyada ve ülkemizde önemli bir çelik üretim ve geri dönüşüm yöntemi olarak bilinen Elektrik Ark Ocakları, yüksek elektrik enerjisi sarfiyatı ile çalışmaktadır. Geçmişten günümüze dek üretim maliyetlerinin düşürülmesi ve ... -
High temperature wear behavior of the surface-modified externally cooled rolls
Günen, Ali; Kanca, Erdoğan; Karakaş, Mustafa Serdar; Koç, Vahdettin; Gök, Mustafa Sabri; Kanca, Yusuf; Çürük, Ahmet; Demir, Mehmet (Elsevier, 2018)Externally cooled rolls of a steel plant were coated using three different surface modification techniques, namely titanizing, boronizing and borotitanizing. The grown coatings were examined using optical microscopy, ... -
Investigation of the wear behavior of FeNi36 alloy cut by WEDM method under different loads
Ceritbinmez, Ferhat; Kanca, Yusuf; Tuna, Ahmet; Kanca, Erdoğan (Emerald Publishing, 2023)PurposeFeNi36 (Invar-36) alloy is widely used in the fabrication of molding tools in aerospace industries but there remains a need to improve its wear and friction performance due to its relatively low hardness. The formation ... -
An investigation on optimum grinding system and conditions for steel plant ARP by-product α-Fe2O3 for pigment industry
Karakaş, Özgür; Kanca, Erdoğan (Elsevier B.V., 2020)After some other processes, ?-Fe2O3 red powder particles -by-product of regeneration of spent pickling liquor in ARP in iron and steel industry- should be ground up to pigment grade to convert it to a value added product, ... -
An investigation on optimum grinding system and conditions for steel plant ARP by-product α-Fe2O3 for pigment industry
Karakaş, Özgür; Kanca, Erdoğan (Elsevier, 2020)After some other processes, α-Fe2O3 red powder particles -by-product of regeneration of spent pickling liquor in ARP in iron and steel industry- should be ground up to pigment grade to convert it to a value added product, ... -
Investigations on machinability of Al2O3 reinforced Al6061 metal matrix composites
Kanca, Erdoğan; Günen, Ali (Süleyman Demirel Üniversitesi Fen Bilimleri Enstitüsü Dergisi, 2016)In this study, six different MMCs containing Al6061 matrix and Al2O3reinforcements with particle sizes of 32 µm and 66 µm and weight fraction of 10%, 15% and 20% were produced using the vortex method. Machinability ... -
Jominy testinin sonlu elemanlar yöntemiyle modellenmesi
Yürük, Soner (İskenderun Teknik Üniversitesi / Mühendislik ve Fen Bilimleri Enstitüsü / Makine Mühendisliği Anabilim Dalı, 2018)Malzemelere uygulanan ısıl işlemlerin modellenebilmesi günümüzde ticari yazılımlarla yapılmaktadır. Bu modellemeleri yapan ticari programlar, iş parçasının ısıl işlem sonrasındaki mekanik özellikleri ve tane yapıları ... -
Karbon nanotüp ve cam elyaf takviyeli yüksek yoğunluklu polietilen hibrit kompozit malzemelerin mekanik özelliklerinin iyileştirilmesi
Tanın, Mihrap (İskenderun Teknik Üniversitesi / Mühendislik ve Fen Bilimleri Enstitüsü / Makine Mühendisliği Anabilim Dalı, 2016)Bu çalışmada yüksek yoğunluklu polietilen (YYPE), karbon nano tüp (KNT) katkılı YYPE , cam elyaf takviyeli YYPE ve KNT katkılı cam elyaf takviyeli YYPE malzemelerin mekanik özellikleri incelenmiştir. Granül halindeki YYPE’ ... -
Microabrasion Wear Behavior of Fast-Borided Steel Tooth Drill Bits
Günen, Ali; Kanca, Erdoğan; Demir, Mehmet; Er, Yusuf; Sağlam, Gökhan; Gök, Mustafa Sabri (Taylor and Francis Inc., 2017)In this study, the surface of steel tooth drill bits (Ni-Cr-Mo based) was subjected to the solid-state boriding treatment with 10- to 50-nm nanoboron powder. Boriding processes were carried out at a constant temperature ... -
Microstructural and mechanical properties of friction stir welded pure lead
Günen, Ali; Kanca, Erdoğan; Demir, Mehmet; Çavdar, Faruk; Mıstıkoğlu, Selçuk; Çam, Gürel (National Institute of Science Communication and Information Resources (NISCAIR), 2018)The present study focuses on the applicability of friction stir welding to pure Pb plates. The joint performances are evaluated by optical microscopy, microhardness measurements, notch impact tests and three point bending ... -
Microstructure and mechanical properties of borided inconel 625 superalloy
Günen, Ali; Kanca, Erdoğan (Universidade Federal do Rio de Janeiro, 2017)The Ni-based superalloy Inconel 625 is extensively used owing to its high strength, excellent fabricability, good weldability and outstanding resistance to high temperature corrosion against aggressive environments. However, ... -
A Modeling Study on Surface Roughness of Spinneret Mold Sections Machined By WEDM
Kanca, Erdoğan; Taşkın, Volkan Cem; Günen, Ali (Sakarya University Journal of Science, 2019)The Wire Electrical Discharge Machining (Wire EDM) is widely used in the cutting of Bulk Continuous Filament (BCF) spinneret molds. Because of the low surface roughness of the spinneret molds obtained by the Wire EDM method, ... -
MRR, EWR and KERF Analysis in cold work tool steel machining in EDM method by copper and brass electrode
Ceritbinmez, Ferhat; Gökkaya, Elif Simay; Kanca, Erdoğan (Osmaniye Korkut Ata Üniversitesi, 2023)In this study, holes were drilled on the Sleipner cold work tool steel with a hardness of 60-62 HRC by copper and brass electrodes using three different current values (50, 25, 12.5 A), pulse on times (3, 6, 9 μs) and pulse ... -
Prediction of mechanical properties of cold rolled steel using genetic expression programming
Kanca, Erdoğan; Çavdar, Faruk; Erşen, M. M. (Polish Academy of Sciences, 2016)A new model was developed to predict the mechanical properties of St22 grade cold rolled deep drawing steel by gene expression programming. To obtain a dataset to find out the effect of reduction rate on the mechanical ... -
Properties and Corrosion Behavior of Chromium and Vanadium Carbide Composite Coatings Produced on Ductile Cast Iron by Thermoreactive Diffusion Technique
Günen, Ali; Kalkandelen, Müge; Karahan, İsmail Hakkı; Kurt, Bülent; Kanca, Erdoğan; Gök, Mustafa Sabri; Karakaş, Mustafa Serdar (ASME, 2020)Ductile iron (DI) owes many of its attractive mechanical properties to the graphite nodules in its structure. However, since galvanic coupling can occur between the graphite nodules and the matrix in aggressive environments, ... -
A Response Surface Modeling Study on Effects of Powder Rate and Machining Parameters on Surface Quality of CoCrMo Processed by Powder Mixed Electrical Discharge Machining
Yıldız, Can; Çavdar, Faruk; Kanca , Erdoğan (Giresun Üniversitesi, 2023)Due to the high mechanical strength of the metals used in implant manufacture, which makes them difficult to work with using other machining techniques, electrical discharge machining (EDM) is frequently employed in the ... -
S460MC ince taneli yapı çeliklerinin MAG kaynak yöntemi ile birleştirilmesinde akım ve koruyucu gaz karışımının mikro yapı ve mekanik özelliklere etkisinin incelenmesi
Kargın, Yasin (İskenderun Teknik Üniversitesi / Lisansüstü Eğitim Enstitüsü / Makine Mühendisliği Ana Bilim Dalı, 2022)Bu çalışmada yüksek mukavemetli ince taneli bir çelik olan S460MC çelik plakalar iki farklı koruyucu gaz kompozisyonu ve iki farklı kaynak akımı değerlerinde, kaynak hızı sabit tutulup MAG (Metal Aktif Gaz) kaynak ...