• Designing, Modeling and Simulation of Solid Fuel Rocket ALP-01 

  Bilgiç, Hasan Hüseyin; Çoban, Sezer; Yapıcı, Ahmet (Avrupa Bilim ve Teknoloji Dergisi, 2019)

  In this study the design of solid-fuel low-altitude rocket ALP-01 CAD has been optimized for the selected engine of rocket sizes foran altitude of 1500 meters. Parabolic type was preferred as the cone geometry. The length ...

• A Study On Prediction of Surface Roughness and Cutting Tool Temperature After Turning For S235JR Steel 

  Bilgiç, Hasan Hüseyin; Güvenç, Mehmet Ali; Çakır, Mustafa; Mıstıkoğlu, Selçuk (Konya Mühendislik Bilimleri Dergisi, 2019)

  In machining technologies, the most important criterion taken into consideration whenevaluating the product quality is seen as the surface roughness. In the consideration of productionquality and cost, tool wear is one of ...

• AISI 304 Östenitik Paslanmaz Çelik Levhaların TIG Kaynağı ile Birleştirilmesinde Farklı Koruyucu Gaz Tiplerinin Mekanik Özelliklerine Etkisi 

  Kahraman, Hasan; Güvenç, Mehmet Ali; Mıstıkoğlu, Selçuk (Journal of Materials and Mechatronics:A (Online), 2021)

  AISI 304 kalite Östenitik paslanmaz çelikler, paslanmaz çelikler arasında en çok kullanılan kalitelerden biridir. Kimyasal bileşimin ve mekanik özellikleri sayesinde kolay işlenebilir ve şekil alabilir olması, kaynaklanabilme ...

• Esnek Robot Kol Sistemi İçin LQR Denetleyici Parametrelerinin Metasezgisel Algoritmalar Kullanılarak Belirlenmesi 

  Özkaya, Semih; Conker, Çağlar; Bilgiç, Hasan Hüseyin (Konya Mühendislik Bilimleri Dergisi, 2021)

  Sunulan çalışma, bir esnek robot kol sisteminin hareket kontrolüne yönelik LQR denetleyici tasarımı ile kontrol parametrelerinin optimizasyonu hakkında ayrıntılı analizler sunmaktadır. Optimizasyonun temel amacı esnek robot ...

• Sleipner Soğuk İş Takım Çeliğinin Elektro-Erozyon Tezgahında Bakır Krom Zirkonyum Alaşımı Elektrot ile İşlenmesinde İşleme Parametrelerinin Kerf ve Yüzey Pürüzlülüğü Üzerine Etkisinin İncelenmesi 

  Ceritbinmez, Ferhat; Yapıcı, Ahmet (Karadeniz Fen Bilimleri Dergisi, 2021)

  Bu çalışmada 60-62 HRC sertlik değerine sahip Sleipner Soğuk İş Takım Çeliğinden Bakır Krom Zirkonyum Alaşımı Elektrot kullanılarak elektro erozyon işleme (EEİ) yöntemi ile talaş kaldırılmıştır. Bu kapsamda üç farklı boşalım ...

• 3B Yazıcıların Mesleki Ve Teknik Eğitimdeki Uygulamalarının Ve Potansiyellerinin İncelenmesi: İskenderun Meslek Yüksekokulu Örneği 

  Çakır, Mustafa; Mıstıkoğlu, Selçuk (International Journal of 3D Printing Technologies and Digital Industry, 2021)

  3B (3 boyutlu) yazıcılar her geçen gün hayatımıza biraz daha eklemlenmektedirler. Buradaki en önemli etki hiç şüphesiz her geçen gün ucuzlayan fiyatları ve yeni kullanım alanlarının keşfidir. 3B yazıcıların eğitimde özellikle ...

• Comparison of pure-hydrogen production performances of blast furnace slag, and metal powders in sodium borohydride hydrolysis reaction 

  İskenderoğlu, Feride Cansu; Baltacıoğlu, Mustafa Kaan (2022)

  In this study, hydrolysis reaction performances of raw BFS powder and metal powders (which are ingredients of BFS) that are using as a catalyst are compared. Hydrogen generation by hydrolysis reaction of the Al and Fe2O3 ...

• Numerical Examination of A Solar Chimney Power Plant Designed for the Iskenderun Region 

  Önal, Mustafa; Koç, Ali; Köse, Özkan; Koç, Yıldız; Yağlı, Hüseyin (Konya Mühendislik Bilimleri Dergisi, 2022)

  Today, energy is accepted as the most indicator of economic development. However, the use of fossil fuels as energy sources is caused the depletion of the ozone layer, global warming and climate change. Therefore, using ...

• An autonomous hydrogen production system design based on the solid chemical hydride 

  İskenderoğlu, Feride Cansu; Baltacıoğlu, Mustafa Kaan; Conker, Çağlar; Bilgiç, Hasan Hüseyin (European Mechanical Science, 2022)

  This paper develops a hydrogen generator prototype that is for fuel cell systems used in portable applications. This generator is designed based on the use of solid-state hydrides with high hydrogen storage capacity in the ...

• The Effects of Cutting Parameters Used in Milling X153CrMoV12 Cold Work Tool Steel by End Mills on Surface Roughness and Hardness of The Workpiece 

  Ceritbinmez, Ferhat; Kanca, Erdoğan (Gazi University, 2022)

  The goal of this project is to investigate the effect of the spindle speed and feed rate used in milling X153CrMoV12 cold work steel by X5070 blue coated solid carbide end mill on surface roughness and hardness of the ...

• Multi-pass butt welding of thick AISI 316L plates by gas tungsten arc welding: Microstructural and mechanical characterization 

  Serindağ, Hüseyin Tarık; Çam, Gürel (Elsevier, 2022)

  Austenitic stainless steels exhibit excellent properties such as outstanding formability even at cryogenic temperatures, high mechanical properties and good corrosion performance. This makes them attractive for use in ...

• A comparative study of estimating solar radiation using machine learning approaches: DL, SMGRT, and ANFIS 

  Üstün, İsmail; Üneş, Fatih; Mert, İlker; Karakuş, Cuma (Taylor and Francis Ltd., 2022)

  Solar energy has a key role in producing clean and emissions-free power compare to conventional methods. However, sustainable development also requires a reliable and predictable energy source. It also needs methods to ...

• Pinch point determination and Multi-Objective optimization for working parameters of an ORC by using numerical analyses optimization method 

  Kocaman, Emrullah; Karakuş, Cuma; Yağlı, Hüseyin; Koç, Yıldız; Yumrutaş, Recep; Koç, Ali (Elsevier, 2022)

  In parallel with Kyoto, Paris and the green production agreements, the nowadays crucial subject is minimising energy consumption, increasing renewable energy usage and recovering waste heat. When it comes to waste heat, ...

• Sinusoidally located concrete metastructures for attenuation of seismic surface vibrations 

  Kaçın, Selçuk; Öztürk, Murat; Sevim, Umur Korkut; Karaaslan, Muharrem; Akgöl, Oğuzhan; Özer, Zafer; Demirci, Mustafa; Ünal, Emin; Mert, Bayram Ali; Alkurt, Maide Erdoğan; Alkurt, Fatih Özkan; Başar, Mustafa Tunahan; Kaya, Şeyda Gülsüm (Springer, 2022)

  In this numerical and experimental study, we designed sinusoidal located concrete-based boreholes which are candidate for seismic shielding applications. To attenuate seismic wave transmission in an area, proposed design ...

• Effect of the boriding environment on the wear response of laser-clad AlCoCrFeNi high entropy alloy coatings 

  Günen, Ali; Lindner, Thomas; Karakaş, Mustafa Serdar; Kanca, Erdoğan; Töberling, Gerd; Vogt, Sabrina; Gök, Mustafa Sabri; Lampke, Thomas (Elsevier, 2022)

  Laser-clad AlCrFeCoNi high entropy alloy (HEA) coatings, produced on the surface of AISI 316 L stainless steel, were pack-borided at 1000 °C for 4 h in open air, high-purity Ar and vacuum environments. The HEA, which had ...

• Surface integrity characteristics in wire-EDM of HfTaTiVZr refractory high entropy alloy 

  Ceritbinmez, Ferhat; Günen, Ali; Akhtar, Mst Alpona; Patel, Kunjal; Mukherjee, Sundeep; Yünlü, Lokman; Kanca, Erdoğan (Taylor and Francis Ltd., 2022)

  Refractory high entropy alloys (RHEAs) with multiple principal elements constitute a new paradigm in alloy design and have gained recent interest for advanced technical applications due to their unique properties and ...

• A review on drilling of FML stacks with conventional and unconventional processing methods under different conditions 

  Doğan, Mehmet Akif; Yazman, Şakir; Gemi, Lokman; Yıldız, Murat; Yapıcı, Ahmet (Elsevier, 2022)

  Fiber and metal materials used in Fiber Metal Laminate (FML) have different machinability properties due to their different structures. This case has made it a research topic to obtain good hole quality in these materials. ...

• The prediction of surface roughness and tool vibration by using metaheuristic-based ANFIS during dry turning of Al alloy (AA6013) 

  Güvenç, Mehmet Ali; Bilgiç, Hasan Hüseyin; Çakır, Mustafa; Mıstıkoğlu, Selçuk (Springer, 2022)

  In this article, the adaptive neuro-based fuzzy inference system (ANFIS) model is developed to estimate the surface roughness (Ra) and tool vibrations (Acc) of AA6013 aluminum alloy during dry turning. Turning experiments ...

• Effect of boronizing on microstructure, high-temperature wear and corrosion behavior of additive manufactured Inconel 718 

  Kayalı, Yusuf; Kanca, Erdoğan; Günen, Ali (Elsevier, 2022)

  In this study, Ni-based Inconel 718 coatings were additively manufactured on the surface of AISI H13 work tool steel by electro-spark deposition (ESD). Some of the electro-spark deposited samples were boronized at 1000 ? ...

• A study on microstructure and mechanical performance of gas metal arc welded AISI 304 L joints 

  Ezer, M. A.; Çam, Gürel (Wiley, 2022)

  Arc welding is a widely applied process in the fabrication of stainless steel structures. Various difficulties may arise in joining of these steels, particularly if high heat input is used. The main aim of this study is ...

View more