Başlık için Makale Koleksiyonu listeleme
Toplam kayıt 186, listelenen: 123-142
-
Low Velocity Impact and Tensile Performance of GFRPs Interleaved with Electrospun Nylon 6,6 Nanofiber Mats
(Strojarski Facultet, 2021)Nanofibers can be interleaved into polymers and improvements in mechanical properties such as resistance to impact, delamination and debonding as well as enhanced ductility can be obtained. In this work, GFRP laminated ... -
The mechanical effect of functionalization in laminated composite material
(Emerald Publishing, 2023)PurposeThis study aims to systematically compare the effect of increasing fiber-matrix interface adhesion and matrix toughness in layered composite materials. Design/methodology/approachSilane ((3-glycidyloxypropyl) ... -
Mechanical properties of friction stir welded St 37 and St 44 steel joints
(Carl Hanser Verlag, 2018)In this study, the weldability of lower strength St 37 grade steel plate with a higher strength steel plate (i. e., St 44) using the friction stir welding technique has been studied. St 37 grade steel sheets are widely ... -
Meta-Heuristic Tuning of the LQR Weighting Matrices Using Various Objective Functions on an Experimental Flexible Arm Under the Effects of Disturbance
(Springer, 2021)In this paper, meta-heuristic tuning of LQR weighting matrices using various objective functions on the experimental flexible arm under the effects of disturbance is investigated. The use of flexible and lightweight systems ... -
Microabrasion Wear Behavior of Fast-Borided Steel Tooth Drill Bits
(Taylor and Francis Inc., 2017)In this study, the surface of steel tooth drill bits (Ni-Cr-Mo based) was subjected to the solid-state boriding treatment with 10- to 50-nm nanoboron powder. Boriding processes were carried out at a constant temperature ... -
Microstructural and Mechanical Properties of Friction Stir Welded Nickel-Aluminum Bronze (NAB) Alloy
(Springer, 2016)In this study, the applicability of friction stir welding to cast NAB alloy (i.e., C95800) with a thickness of 9 mm has been investigated. The joint performance was determined by conducting optical microscopy, microhardness ... -
Microstructural and mechanical properties of friction stir welded pure lead
(National Institute of Science Communication and Information Resources (NISCAIR), 2018)The present study focuses on the applicability of friction stir welding to pure Pb plates. The joint performances are evaluated by optical microscopy, microhardness measurements, notch impact tests and three point bending ... -
Microstructure and mechanical properties of borided inconel 625 superalloy
(Universidade Federal do Rio de Janeiro, 2017)The Ni-based superalloy Inconel 625 is extensively used owing to its high strength, excellent fabricability, good weldability and outstanding resistance to high temperature corrosion against aggressive environments. However, ... -
Microstructure and mechanical properties of friction-stir welded St52 steel joints
(Springer, 2018)The aim of this work is to investigate the mechanical properties and microstructures of friction-stir welded (FSWed) St52 structural steel joints. In this study, St52 steel plates with a thickness of 4 mm were butt-welded ... -
Microstructure, some mechanical properties and tribocorrosion wear behavior of boronized Al0.07Co1.26Cr1.80Fe1.42Mn1.35Ni1.10 high entropy alloy
(Elsevier, 2021)High-entropy alloys (HEAs) with face-centered cubic (FCC) structures exhibit high toughness and corrosion resistance, but their average strengths and relatively low wear resistance can limit their engineering ap-plications. ... -
Microwave absorption performance of hexagonal nano boron nitride doped basalt fabric-reinforced epoxy composites
(Emerald Group Publishing Ltd., 2021)Purpose: The purpose of this paper is to investigate the effect of doping element on the microwave absorption performance of hexagonal nano boron nitride (h-nBN)-reinforced basalt fabric (BF)/epoxy composites. A new type ... -
Modeling and Optimization of a Peano-HASEL Actuator Peristaltic Pump
(National Institute of Science Communication and Policy Research, 2023)Peano-Hasel (hydraulically amplified self-healing electrostatic) pumps are crucial devices with unique mechanisms and versatile applications. They simulate muscle contractions to move fluids or materials through tubes. The ... -
Modeling of a Combined Kalina and Organic Rankine Cycle System for Waste Heat Recovery from Biogas Engine
(MDPI, 2022)Converting waste heat into electricity has captured the interest of scientists for years because of its enormous potential to improve energy efficiency and to lessen environmental impacts. While there are numerous applications ... -
A Modeling Study on Surface Roughness of Spinneret Mold Sections Machined By WEDM
(Sakarya University Journal of Science, 2019)The Wire Electrical Discharge Machining (Wire EDM) is widely used in the cutting of Bulk Continuous Filament (BCF) spinneret molds. Because of the low surface roughness of the spinneret molds obtained by the Wire EDM method, ... -
MRR, EWR and KERF Analysis in cold work tool steel machining in EDM method by copper and brass electrode
(Osmaniye Korkut Ata Üniversitesi, 2023)In this study, holes were drilled on the Sleipner cold work tool steel with a hardness of 60-62 HRC by copper and brass electrodes using three different current values (50, 25, 12.5 A), pulse on times (3, 6, 9 μs) and pulse ... -
Multi-pass butt welding of thick AISI 316L plates by gas tungsten arc welding: Microstructural and mechanical characterization
(Elsevier, 2022)Austenitic stainless steels exhibit excellent properties such as outstanding formability even at cryogenic temperatures, high mechanical properties and good corrosion performance. This makes them attractive for use in ... -
MWCNTs doped GFRPs drilling: crosscheck among holes obtained by alternative manufacturing methods
(Springer, 2021)In this study, the holes of glass fiber reinforced polymer (GFRP) and multi-walled carbon nanotubes (MWCNTs) doped GFRP composite materials were drilled using abrasive water jet (AWJ), CO2 laser cutting, orbital drilling, ... -
A new approach to improve some properties of wire arc additively manufactured stainless steel components: Simultaneous homogenization and boriding
(Elsevier, 2023)Arc-directed energy deposition (Arc-DED), also commonly referred to as wire arc additive manufacturing (WAAM), is a cost-effective 3D metal additive manufacturing process in which large metallic parts can be produced due ... -
A new hybrid meta-heuristic optimization method for predicting UTS for FSW of Al/Cu dissimilar materials
(SAGE Publications, 2023)Joining of aluminum (Al) and copper (Cu) materials used in aerospace, automotive, chemistry, nuclear, electrical-electronic and energy sector with traditional fusion welding methods has some negative consequences. One of ... -
Numerical Examination of A Solar Chimney Power Plant Designed for the Iskenderun Region
(Konya Teknik Üniversitesi, 2022)Today, energy is accepted as the most indicator of economic development. However, the use of fossil fuels as energy sources is caused the depletion of the ozone layer, global warming and climate change. Therefore, using ...
