Başlık için Makale Koleksiyonu listeleme
Toplam kayıt 186, listelenen: 102-121
-
Harmonic response analysis of an impeller of a gas turbine engine which modelled by using high entropy alloy materials
(Gümüşhane Üniversitesi, 2022)One of the problems in a gas turbine’s impeller design is to predict the frequency-stress response caused by the harmonic force resulted from the unbalanced mass. To avoid from impeller’s flaws that may occur, designers ... -
Hayvan Gübresinden Biyogaz Üretim Potansiyelinin Belirlenmesi: Adana İli Örnek Hesaplama
(Çukurova Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, 2019)Bu çalışmada, Adana İli için biyogaz üretimi ve üretilen bu biyogazın kullanımı ile elde edilebilecek güç miktarının tespiti yapılmıştır. Çalışma kapsamında öncelikle Adana ilinde bulunan tüm hayvan sayıları (kanatlı, büyük ... -
HHO enrichment of bio-diesohol fuel blends in a single cylinder diesel engine
(Elsevier Ltd, 2019)One of the primary aims of this experimental investigation is to examine hydroxy-gas enrichment effects on environmentally friendly but performance-reducing alternative fuels such as ethanol and biodiesel. Hydroxy gas is ... -
High temperature wear behavior of the surface-modified externally cooled rolls
(Elsevier, 2018)Externally cooled rolls of a steel plant were coated using three different surface modification techniques, namely titanizing, boronizing and borotitanizing. The grown coatings were examined using optical microscopy, ... -
Identification Of Chatter Vibrations And Active Vibration Control By Using The Sliding Mode Controller On Dry Turning Of Titanium Alloy (TI6AL4V)
(University of Nis, 2023)In recent years, with the development of sensor technologies, communication platforms, cyber-physical systems, storage technologies, internet applications and controller infrastructures, the way has been opened to produce ... -
Improving Autonomous Performance of a Passive Morphing Fixed Wing UAV
(Kauno Technologijos Universitetas, 2020)In this article, simultaneous longitudinal and lateral flight control systems design for both passive and active morphing unmanned aerial vehicles (UAVs) is first time applied for autonomous flight performance maximization. ... -
Investigation into microstructures and properties of AISI 430 ferritic steel butt joints fabricated by GMAW
(Elsevier, 2023)Heat input is extremely important for achieving joints with high mechanical properties in ferritic stainless steels. Thus, one of the objectives of this study is to show the effect of heat input on microstructural evolution ... -
Investigation of cotton fabric composites as a natural radar-absorbing material
(Emerald Group Publishing Ltd., 2020)Purpose The purpose of this paper is to investigate cotton fabric behavior that is exposed to radar waves between selected operation frequencies as an alternative radar-absorbing material (RAM) response. Cotton fabric ... -
Investigation of electromagnetic properties of glass-fiber reinforced epoxy composites containing pan nanofibers with mwcnt/graphene additive
(Parlar Scientific Publications (P S P), 2019)In this work; the differences between of electromagnetic properties of glass fiber reinforced (GFR)-epoxy laminate composites with various nanoparticle doped polyacrylonitrile (PAN) fibers were investigated. The laminated ... -
Investigation of methanol contaminated local spirit using metamaterial based transmission line sensor
(Elsevier, 2021)A metamaterial-based transmission line sensor was designed to determine the amount of methanol in methanol-contaminated local spirit samples both numerically and experimentally. The proposed sensor consists of a square ... -
Investigation of microstructure and mechanical properties of friction stir welded dissimilar St37/St52 joints
(Institute of Physics Publishing, 2019)Although friction stir welding (FSW) has widely been applied to aluminum alloys in several industries over the past three decades, it is not yet used in industry for joining of steels. The aim of this study is to characterize ... -
An Investigation of Punching the MWCNTs Doped Composite Plates by Using Different Cutting Profiles
(University of Osijek, 2021)In this study, glass fiber reinforced composite layers which are with and without additives of 0.1 wt.% multi walled carbon nanotubes (MWCNTs) of epoxy were manufactured by vacuum infusion method. Unlike the conventional ... -
Investigation of the wear behavior of FeNi36 alloy cut by WEDM method under different loads
(Emerald Publishing, 2023)PurposeFeNi36 (Invar-36) alloy is widely used in the fabrication of molding tools in aerospace industries but there remains a need to improve its wear and friction performance due to its relatively low hardness. The formation ... -
An investigation on cutting of the MWCNTs doped composite plates by CO2 laser beam
(Emerald Group Publishing Ltd., 2022)Purpose The purpose of this study is to obtain strong materials with multiwall carbon nanotubes (MWCNTs) doped and investigate laser cut of MWCNTs also find the effect of the laser cutting parameters on composite materials. ... -
An Investigation on Cutting of the MWCNTs-Doped Composite Plates by AWJ
(Springer Heidelberg, 2020)In this study, cutting of multi-walled carbon nanotubes (MWCNTs)-doped composite sheets by abrasive water jet machining (AWJM) and the effects of the water jet on cut composite materials were analyzed. The influence of ... -
An investigation on optimum grinding system and conditions for steel plant ARP by-product α-Fe2O3 for pigment industry
(Elsevier B.V., 2020)After some other processes, ?-Fe2O3 red powder particles -by-product of regeneration of spent pickling liquor in ARP in iron and steel industry- should be ground up to pigment grade to convert it to a value added product, ... -
An investigation on optimum grinding system and conditions for steel plant ARP by-product α-Fe2O3 for pigment industry
(Elsevier, 2020)After some other processes, α-Fe2O3 red powder particles -by-product of regeneration of spent pickling liquor in ARP in iron and steel industry- should be ground up to pigment grade to convert it to a value added product, ... -
Investigations on machinability of Al2O3 reinforced Al6061 metal matrix composites
(Süleyman Demirel Üniversitesi Fen Bilimleri Enstitüsü Dergisi, 2016)In this study, six different MMCs containing Al6061 matrix and Al2O3reinforcements with particle sizes of 32 µm and 66 µm and weight fraction of 10%, 15% and 20% were produced using the vortex method. Machinability ... -
Is Kalina cycle or organic Rankine cycle for industrial waste heat recovery applications? A detailed performance, economic and environment based comprehensive analysis
(Elsevier, 2022)Contrary to the increase in energy demand throughout the world, fossil fuels, which are the main energy source, is now more difficult to reach because of the pandemic, transport or bilateral relations, etc. These obstacles ... -
Isı-güç kombine sistemlerinde kullanılan kalina çevriminin enerji ve ekserji analizi
(Politeknik Dergisi, 2020)Küresel ısınmanın giderek arttığı ve hava kirliliğinin insan sağlığını hissedilebilir şekilde tehdit ettiği bugünlerde, enerjiye olan ihtiyaç da giderek artmaktadır. Bu nedenle sadece insanların enerji ihtiyacını karşılamak ...
