Ara
Toplam kayıt 175, listelenen: 61-70
Analysing the performance, fuel cost and emission parameters of the 50 MW simple and recuperative gas turbine cycles using natural gas and hydrogen as fuel
(Elsevier, 2020)
In the present study, firstly, the power production, thermal and exergy efficiencies were calculated for the simple and recuperative gas turbine cycles at constant power production (50 MW) and turbine outlet temperature ...
The effects of interface and matrix reinforcements on fracture toughness of E-Glass/epoxy laminate
(Institute of Physics Publishing, 2020)
In this study, the effects of low amount (0.1 wt%) multi-walled carbon nanotube (MWCNTs) distributed homogenously in epoxy via cationic surfactant (cetyl pyridiniumchloride-CPC), polyacrylonitrile nanofiber (in the range ...
Friction stir welding of AZ31 magnesium alloys – A numerical and experimental study
(Brazilian Association of Computational Mechanics, 2017)
In this paper, weldability of magnesium alloys by friction stir welding (FSW) method which is difficult to join by the fusion welding have been investigated experimentally and numerically. To this end, the connection of ...
Quantized control settings based tuning of a heaving wave energy converter in irregular seas
(Taylor and Francis Inc., 2016)
The increasing awareness of environmental issues attracts more attention on environmentally friendly energy sources. This leads to increasing research on effective use of renewable energy sources. Among them, wave energy ...
Mechanical properties of friction stir welded St 37 and St 44 steel joints
(Carl Hanser Verlag, 2018)
In this study, the weldability of lower strength St 37 grade steel plate with a higher strength steel plate (i. e., St 44) using the friction stir welding technique has been studied. St 37 grade steel sheets are widely ...
Determination of Barreling of Aluminum Solid Cylinders During Cold Upsetting Using Genetic Algorithm
(UNIV FED RIO DE JANEIRO, LAB HIDROGENIO, 2019)
This study presents Genetic Programming models for the formulation of barreling of aluminum solid cylinders during cold upsetting based on experimental results. The maximum and minimum radii of the barreled cylinders having ...
Microstructural and Mechanical Properties of Friction Stir Welded Nickel-Aluminum Bronze (NAB) Alloy
(Springer, 2016)
In this study, the applicability of friction stir welding to cast NAB alloy (i.e., C95800) with a thickness of 9 mm has been investigated. The joint performance was determined by conducting optical microscopy, microhardness ...
Artificial Intelligence Applications for Friction Stir Welding: A Review
(Korean Institute of Metals and Materials, 2020)
Advances in artificial intelligence (AI) techniques that can be used for different purposes have enabled it to be used in many different industrial applications. These are mainly used for modeling, identification, optimization, ...
Exergy analysis and performance improvement of a subcritical/supercritical organic Rankine cycle (ORC) for exhaust gas waste heat recovery in a biogas fuelled combined heat and power (CHP) engine through the use of regeneration
(MDPI, 2019)
In the present study, a subcritical and supercritical regenerative organic Rankine cycle (rORC) was designed. The designed rORCs assist a combined heat and power (CHP) engine, the fuel of which is biogas produced from ...
Sıcak Presleme Yöntemi ile Üretilmiş Uçucu Kül Takviyeli Bronz Matrisli Fren Balata Malzemelerinin Sürtünme-Aşınma Özellikleri Üzerine Kolemanit Miktarının Etkisi
(Gazi Üniversitesi, 2016)
Bu çalışmada sıcak presleme yöntemi ile üretilen kütlece % 6 uçucu kül takviyeli bronz matrisli fren balata malzemesinin tribolojik özellikleri üzerine farklı oranlarda (% 0,5-4) ilave edilen kolemanit miktarının etkisi ...