Konu "Friction" için Araştırma Çıktıları | Web of Science İndeksli Yayınlar Koleksiyonu listeleme
Toplam kayıt 35, listelenen: 21-35
-
Microstructural and mechanical properties of friction stir welded pure lead
(National Institute of Science Communication and Information Resources (NISCAIR), 2018)The present study focuses on the applicability of friction stir welding to pure Pb plates. The joint performances are evaluated by optical microscopy, microhardness measurements, notch impact tests and three point bending ... -
Microstructural and Tribological Behavior of Pack-Borided Ni-Based Hastelloy C-276 Superalloy
(Springer, 2022)Although the toughness and corrosion resistance of Ni-based superalloys are high due to their face-centered-cubic structure, their surface hardness and, thus, wear resistance are not satisfactory. The boriding process is ... -
Microstructural characterization, boriding kinetics and tribo-wear behavior of borided Fe-based A286 superalloy
(Elsevier, 2022)Iron-based superalloys are alloys produced for use in corrosive environments as an alternative to high-cost nickel-based superalloys. However, their average strength and hardness, attributed to their austenitic structures, ... -
Microstructure and mechanical properties of friction-stir welded St52 steel joints
(Springer, 2018)The aim of this work is to investigate the mechanical properties and microstructures of friction-stir welded (FSWed) St52 structural steel joints. In this study, St52 steel plates with a thickness of 4 mm were butt-welded ... -
Microstructure, some mechanical properties and tribocorrosion wear behavior of boronized Al0.07Co1.26Cr1.80Fe1.42Mn1.35Ni1.10 high entropy alloy
(Elsevier, 2021)High-entropy alloys (HEAs) with face-centered cubic (FCC) structures exhibit high toughness and corrosion resistance, but their average strengths and relatively low wear resistance can limit their engineering ap-plications. ... -
A new approach to improve some properties of wire arc additively manufactured stainless steel components: Simultaneous homogenization and boriding
(Elsevier, 2023)Arc-directed energy deposition (Arc-DED), also commonly referred to as wire arc additive manufacturing (WAAM), is a cost-effective 3D metal additive manufacturing process in which large metallic parts can be produced due ... -
A new hybrid meta-heuristic optimization method for predicting UTS for FSW of Al/Cu dissimilar materials
(SAGE Publications, 2023)Joining of aluminum (Al) and copper (Cu) materials used in aerospace, automotive, chemistry, nuclear, electrical-electronic and energy sector with traditional fusion welding methods has some negative consequences. One of ... -
Properties and High Temperature Dry Sliding Wear Behavior of Boronized Inconel 718
(Springer, 2020)Silicide-free boride layers were grown on Inconel 718 Ni-based superalloy surface at 850 degrees C, 950 degrees C, and 1050 degrees C for 2, 4, 6 hour by the powder pack-boronizing process using nano-sized B4C powders. The ... -
Properties and High-Temperature Wear Behavior of Remelted NiCrBSi Coatings
(Springer, 2020)Remelted NiCrBSi coatings were examined using optical microscopy, scanning electron microscopy, energy dispersive spectroscopy, x-ray diffraction analysis, microhardness and wear testing. After wear tests, the surfaces of ... -
Properties and tribological performance of ceramic-base chromium and vanadium carbide composite coatings
(Elsevier, 2019)In the current study, the surface of AISI D2 steel was coated with the powder blends of ferro-vanadium (Fe-V) and ferro-chromium (Fe-Cr). The coatings were performed using a thermo-reactive diffusion (TRD) treatment by the ... -
Recent developments in joining of aluminum alloys
(Springer, 2017)The mass saving potential of light-weight materials, such as Al alloys, is beneficial for fuel economy and reducing CO2 emissions. However, the wide-spread use of these alloys has been long hindered due to the difficulty ... -
A response surface study on the grown behavior and some mechanical properties of niobium carbide coatings
(World Scientific, 2023)In this study, response surface methodology was used to examine the effects of temperature and time on the development of niobium carbide coatings on AISI D3 steel. The effect of niobizing temperature (900-1100C) and period ... -
Sliding Wear and Friction Performance of Pack-Borided Co–28Cr–6Mo Alloy in Physiological Lubricants
(Springer, 2023)The role of bovine calf serum (BCS) related to the functional performance of synovial fluid on the tribological behavior of borides grown on cobalt-28chromium-6molybdenum (Co-28Cr-6Mo) alloy used in orthopedic prostheses ... -
TTribocorrosion behavior of boronized Co1.19Cr1.86Fe1.30Mn1.39Ni1.05Al0.17B0.04 high entropy alloy
(Elsevier, 2021)Boride layers were grown on the surface of a Co1.19Cr1.86Fe1.30Mn1.39Ni1.05Al0.17B0.04 high-entropy alloy (HEA) by boronizing at temperatures of 900, 950 and 1000 degrees C for 4 h using nanosized boronizing powders. ... -
Wear Behavior of Borided AISI D2 Steel under Linear Reciprocating Sliding Conditions
(Pleiades Publishing, 2019)AISI D2 steel is the most commonly used cold-work tool steel in its grade. In this study, microstructural characterization and some mechanical properties of borided AISI D2 steel samples were investigated. The boriding ...